The
ILC-01xx is a
single sensor
ILC unit which
provides a DC/DC
converter,
and/or signal
conditioning
(velocity to
acceleration),
or amplification
of the signal,
or a combination
of these three
functions in a
single compact
machined
aluminum
box. Units
can only be
configured at
the time of
manufacture
since they are
fully
encapsulated
with special
epoxy resins for
ruggedness and
durability at
assembly. Signal
conversion and
gain options are
exclusive;
only one or the
other may be
specified.
As
a
power
converter,
the
ILC-01
will
allow
the
user
to
supply
a
single
excitation
voltage
(typically
+10
to12
Vdc)
and
provides
a
bipolar
voltage
(±13.2
Vdc)
output
to
the
sensor.
The
order
number
for
an
ILC-01
for
power
conversion
has
the
letter
“D”
as
the
ILC
first
option
indicator.
As
a
signal
conditioner,
it
will
covert
the
standard
angular
velocity
output
of
the
sensor
to
an
angular
acceleration
signal.
(The
calibration
data
sheet
provided
with
the
ILC-01xA
will
specify
the
volts-per-volts
output
of
the
acceleration
signal
at
10
Hz.
and
at
100
Hz.
This
is
a
differential
circuit.
The
gain
at
100
Hz.
will
be
ten
times
that
at
10
Hz).
The
order
number
for
an
ILC
for
signal
conversion
from
velocity
to
acceleration
has
the
letter
“A”
as
the
second
ILC
option
indicator.
As
an
amplifier,
the
ILC
will
supply
an
amplified
signal
with
gain
of
1
to
1000
times
normal
signal
output
level.
Standard
versions
are
available
in
1,
10,
100,
or
1000
times
gain.
The
order
number
for
an
ILC
for
signal
amplification
of
10x
has
the
letter
“G”
as
the
second
ILC
option
indicator.
For
gain
of
100x,
the
letter
“H”
is
specified.
For
gain
of
1000x,
the
letter
“L”
is
specified.
(See
examples
below.)
Note
that
either
gain
or
acceleration
signal
output
can
be
supplied,
not
both.
Power
conversion
only
Signal
conversion
from
velocity
to
acceleration
only
Power
conversion
and
Signal
conversion
from
velocity
to
acceleration Signal
amplification
of
10x
only
Signal
amplification
of
100x
only
Signal
amplification
of
1000x
only
Power
conversion
and
Signal
amplification
of
10x
Power
conversion
and
Signal
amplification
of
100x
only
Power
conversion
and
Signal
amplification
of
1000x
only
Power
conversion
and
Signal
Filtering
Continued:
Cables
required with
the ILC-01xx
In-line-conditioner:
CA-02ASENSOR
to
ILC-01
Cable
(Not
required
with
ARS-09A)
CA-03AILC
to
user
test
equipment
and
power
input
cable
Check
individual
sensor order
sheets to verify
that the
specific
ILC-01xx model
applies to the
specific sensor
you are ordering
since some
limitations
apply.
Models ARS-01S
cannot be used
with power
conversion
options.
Model ARS-09A
(not ARS-09) is
required for use
with ILC box.
Note: The
CA-03A cable has
AirBorn M series
connectors at
the ILC box and
bare ends for
the test
equipment and
power supply
connections.
These require
direct
connection or
customer
supplied
connectors at
the test
equipment and
power supply.
Over
